Well Pump Installation — New System & Replacement Mississauga

Delex Plumbing installs well pump systems throughout Mississauga and surrounding areas — new submersible pump and drop pipe installation, pressure tank sizing and pre-charge, control box wiring, and full system commissioning with water quality testing. Licensed, insured, flat-rate.

When Is a New Well Pump Installation Required?

Properties in the Mississauga area that rely on well water rather than the municipal supply require well pump systems that are correctly sized, correctly installed, and regularly maintained. New pump installation is required in four situations: when an existing pump reaches end of life and replacement is more economical than repeated repair; when the existing pump system is undersized for increased household water demand following a renovation or occupancy increase; when a new well is drilled and needs initial pump equipment installation; and when a property transitions from a shared or municipal supply to a private well.

We assess the well depth, static water level, and required flow rate before specifying a pump. Static water level — the depth to water in a non-pumping well — determines the required pump depth and the suction lift for jet pump systems. Required flow rate is calculated from the fixture count and peak demand schedule for the household. A system sized too small for peak demand will run continuously during high-use periods, burning out the motor prematurely.

For rural properties in Halton Hills, Caledon, Brampton outskirts, and the Mississauga greenbelt fringe, we also evaluate whether the existing well casing condition and diameter can accommodate a modern submersible pump. Older bored wells with 100mm or 150mm casings may require a smaller diameter pump than a standard drilled well with a 150mm or 200mm casing.

A well conversion from a jet pump to a submersible system is a common upgrade we perform. Jet pump systems are less efficient and less reliable than submersible systems for deep wells — they require priming, are affected by surface temperature variations, and cannot match the flow rates of a properly sized submersible pump at depths beyond 25 metres.

Submersible Pump Sizing — Depth, Flow Rate & Horsepower

Submersible pump selection for a Mississauga area well involves matching three parameters: flow rate in litres per minute, total dynamic head, and motor horsepower. Flow rate is determined by the household fixture count — a standard 3-bathroom detached home requires a minimum 45 to 60 litres per minute. Total dynamic head is the sum of the vertical lift from the pump to the pressure tank plus friction losses in the drop pipe and surface plumbing. Motor horsepower must be sufficient to deliver the required flow at the calculated total dynamic head.

We use the well driller’s log — the record of well depth, casing diameter, and static water level prepared when the well was drilled — to determine the correct pump setting depth. Setting the pump too shallow risks pulling air if the water level drops during periods of high demand or drought. Setting the pump too deep increases the vertical lift unnecessarily and reduces pump efficiency.

Drop pipe material for new installations is HDPE (high-density polyethylene) — the current industry standard that replaced galvanized steel in the 1990s and PVC for most applications. HDPE is flexible, corrosion-resistant, and rated for the pressure and temperature conditions inside a well casing. We install HDPE drop pipe with stainless steel submersible pump wire guards to prevent the electrical cable from chafing against the casing or the pipe.

For properties where the existing well pump circuit wiring needs upgrading to accommodate a new pump motor, we coordinate with the licensed electrician required by the Ontario Electrical Safety Code. We specify the circuit requirements and can recommend licensed electricians for the electrical portion of the installation.

Pressure Tank & Control Box — System Integration

Every new well pump installation includes a correctly sized pressure tank and a new control box matched to the pump motor horsepower. The pressure tank size is selected to provide the correct storage volume for the household demand and to limit pump cycles to no more than 6 per hour — the manufacturer-rated maximum for most submersible motors. Under-sized pressure tanks increase cycle frequency and shorten pump life.

We pre-charge the pressure tank to 2 PSI below the pump cut-in pressure — typically 28 PSI for a 30/50 system — before the system is filled with water. This is a critical step that is frequently skipped in inadequate installations. A pressure tank installed with the factory air charge of 18 PSI in a 30/50 system will be effectively waterlogged from first use.

The control box contains the starting capacitor, the run capacitor, and the overload protection relay for the pump motor. We verify that the control box amperage rating matches the installed pump motor and that the overload relay is set to trip at 125% of the pump full-load amp rating — the correct setting for motor protection without nuisance tripping.

System commissioning after installation includes a 30-minute operation test, a pressure cycle count over the test period, a water quality sample collected for the customer, and a written commissioning report noting the pump model, serial number, depth setting, pressure switch settings, and tank pre-charge pressure. We also recommend a water quality test for any newly installed well system before the water is consumed. For existing systems being upgraded, this commissioning report supplements the original well driller’s log in the property records.

Well Pump Installation — Splice Kit & Splice Depth Standards

The electrical splice between the pump motor cable and the drop wire must be made below the static water level and below the pump setting depth — never in the dry zone of the casing. The splice must be made with a waterproof submersible splice kit rated for continuous submersion. A splice made with standard electrical tape and wire nuts in a well casing is a code violation that will fail within months as water wicks into the connection.

We use NSF-certified submersible splice kits for every splice point in the pump circuit inside the well. The splice is assembled with heat-shrink tubing and filled with waterproof sealant before the outer heat-shrink is applied. Each splice is pull-tested before the pump is lowered into the well. A splice that fails after the pump is installed requires pulling the entire pump assembly to repair — a much more costly procedure than proper first-installation quality.

The well cap is the final installation step. We install a vermin-proof, watertight well cap that meets Ontario Ministry of Environment requirements. The cap prevents surface water, insects, and small animals from entering the well and contaminating the water supply. We verify that the electrical conduit enters the cap through a sealed fitting — an open conduit entry is a common contamination pathway in older installations.

For all well pump service across the Mississauga area including Brampton, Oakville, Milton, and Halton Hills — call 416-910-2550, contact us online, or request service. For existing well systems that need diagnosis before a full replacement decision is made, our well pump repair service identifies whether a component repair — pressure tank, pressure switch, control box — can restore function at lower cost than a full pump pull and replace. We provide honest guidance on the repair-versus-replace decision based on the pump age, condition, and the cost difference between the two options for your specific installation. Every new well pump installation we complete includes a written commissioning checklist signed by the installing plumber, confirming all pre-charge pressures, amp draw readings, cycle test results, and water quality sample collection. This checklist is included with the installation package and serves as the baseline reference for all future maintenance visits.

Free Estimate — Call 416-910-2550

Every well pump installation starts with a free site assessment and estimate. Call 416-910-2550 or contact us online to book.

Frequently Asked Questions

Q: How much does well pump installation cost in Mississauga?

A: A full submersible well pump installation including pump, drop pipe, pressure tank, and control box costs $3,500 to $7,500 depending on well depth, pump horsepower, and whether electrical circuit upgrades are needed. Pressure tank replacement alone costs $600 to $1,200. All prices are flat-rate. Call 416-910-2550 for a free site assessment.

Q: How long does well pump installation take?

A: A standard submersible pump installation in an existing well takes 4 to 6 hours. A complete system installation including pressure tank and control box takes 6 to 8 hours. We commission and test the system on the same day as installation.

Q: What size well pump do I need for a Mississauga home?

A: A standard 3-bathroom detached home requires a pump delivering 45 to 60 litres per minute at the installed depth. Pump horsepower ranges from 1/2 HP for shallow wells under 30 metres to 1 HP or larger for deep wells or high-demand properties. We calculate the correct size during the site assessment using the well log and fixture count.

Q: How often should a well pump system be inspected?

A: We recommend annual well pump system inspection including pressure tank pre-charge verification, pressure switch calibration, control box condition check, and a water quality test. Annual inspection identifies deteriorating components before they cause a system failure.

Get Your Free Estimate Today!

Or Give Us A Call: 416-910-2550

Licensed & Insured Trusted Local Plumbers

Fast Response Usually Within 1 Hour

Satisfaction Guaranteed 100% Quality Work